Table of Content
Watch the video at the beginning of the article for instructions on making Fidget Spinner or continue reading instructions below. Nevertheless, it is a great toy that did raise awareness about the ADHD disorder and problems with concentration that some children have. And that led to bigger efforts in helping those Children in coping with the disorder.
Press it together as well as you can and then make sure it spins. Try not to use too much glue or it will all stick together and not spin. Now cut all shapes from the cardboard using Scissors or Scalpel – you will get 2 circles from coin and 2 Fidget Spinner shapes. Depending on your printer and paper used , you may need to cut the borders to keep only the printed template. Thread a piece of string through both holes, then tie the ends together. Cut a long piece of string, about 28 to 30 inches long.
Printable “You Make Me Hap-pea” Card for Father’s Day
White cardstock will work the best here, but you can use any color you want. Flip 1 of your circles over so that the blank side is facing you. Cover the circle with glue, then place the second circle on top, with the design side facing out.
To make a fidget spinner, print out a fidget spinner stencil, cut out the template, and trace around the template onto cardboard or foam with a pencil. Next, use a pair of sharp scissors or a craft knife to cut the fidget spinner base out of the cardboard or foam. Then, pierce a toothpick through the center of the spinner base and wiggle the toothpick around to widen the hole. Finally, cut out 2 small, evenly sized circles, push 1 circle onto each side of the toothpick, and glue them in place. A lot of DIY fidget spinners are made with bearings, plastic, wood, glue, zip ties, caps, cardboard etc.
How to make Fidget Spinner
You can buy packs of colored printer paper from an office-supply store. Print service shops may also sell these sheets individually. You remember the two guys who made the fidget spinner from gallium in #11?
Hold each end of the toothpick between your thumb and index finger and flick the base to make sure it spins properly. Trace the shape of your spinner onto some cardboard or foam. Cut out your chosen fidget spinner stencil and place it onto a sheet of thick cardboard or foam board.
Making a Coin Spinner
I had never used one, but I thought that was clever. I was disappointed when I saw they used a plastic to make it and decided I wanted to make my own all paper fidget spinner. I eventually got a real one and this paper one doesn't spin as well as a legit one with the ball bearing center, but it is fun to make, personalize, and play with.
To keep the stencil in place, try pushing a toothpick through the center of it and slightly into the cardboard. I made this using a Silhouette paper cutter, but it is possible to print off my design and cut it out of paper. Use Toothpick to attach every Cardboard circle on each side of the Fidget spinner. Now put the glue on top of the coins, and attach the second part of the Fidget Spinner on top of them. The easiest way is to find the picture of a Fidget Spinner using your Smartphone, take a sheet of paper, put it on the screen and draw the shape on the paper.
Decorating Your Spinner
Glue a penny or another small coin onto each of the marks to add some weight to your spinner. Putting the toothpick in the exact center of your spinner base will help make sure it is balanced and spins evenly. If you have a fidget spinner already, you can use it as a stencil by tracing around the edges. It takes more effort to spin it than one that has a ball bearing center, but I think that just adds to the appeal.
If you made the circles out of plain printer paper, you should cut 1 cardboard circle out as well. Glue the circles slightly above the spinner base. Turn the spinner on its side so that you can see one of the circles easily. Squeeze a little bit of superglue or hot glue onto the top of the circle, right around the edges of the toothpick. Repeat on the other circle to hold both circles in place on the toothpick.
When you fold the ends of the paper towards the middle, make sure that they align with the central crease. Sharpen the creases by running your fingernail back and forth across the folded edge. You can learn several fidget spinner tricks to impress your friends and keep yourself busy when you are bored. Making sure that your weights are all the same distance from the middle of your spinner will make sure that it is properly balanced and spins evenly. These circles will be used to hold the toothpick in place and make it more comfortable to hold.
Ask a parent or guardian for help to make sure that you don't hurt yourself. They are fun and entertaining, and they pass the time when you're bored. They also allow you to fidget with them instead of having to move your body or legs around. A pair of wire cutters or something similar will be the easiest way to cut through the toothpick cleanly. You could also use a small file to saw off the end of the toothpick to a smooth finish. The wikiHow Video Team also followed the article's instructions and verified that they work.
Origami Finger Fidget spinner made with the colored printable template. Decorate the circles with crayons, markers, or colored pencils. You can create whatever pattern you want, but keep in mind that these circles will spin.
If your circles don't line up well, you can try to shave them down with sandpaper or a nail file. I'll put the supplies I used for my Silhouette version and also my suggested supplies if you decide to print and hand cut it. Using Scissors, cut the extra Toothpick on every side so it is aligned with the circles.
Handmade 3d Valentines Cards
You should have an X-shaped crease in the middle. If you want to decorate it with your own pattern, wait until after you have finished making the fidget spinner. You can use patterned scrapbooking paper, as long as it is the same weight and thickness as printer paper. Be careful not to widen the hole too much, as this will make your spinner wobble while it spins. It should be just big enough that it can spin around the toothpick with little resistance.
Make sure that they are centered, however; otherwise, the disk won't spin. You only need to design 1 side of each circle. You may notice that your strips have 2 seams on the front, and 1 seam on the back. Stack the strips together with the fronts facing each other so that they make an X shape. You should have 1 seam on the front of the stack, and 1 seam on the back. Fold the corners up so that they are perpendicular to the strip.
No comments:
Post a Comment